Skip to content

Best time to run

Best time to run answers one question: if I run this at a different time, what changes? Pick an appliance, and a day chart shows every possible start time as a bar, so you can see at a glance when it’s cheap and when it isn’t. It’s free on every plan and sits on the Insights page.

  1. Open Explore → Insights and find the Best time to run card. Tap it to open the tool.
  2. Choose an appliance: pool pump, EV charging, water heater, dryer, dishwasher, central AC pre-cool, mini split pre-cool, oven pre-cook, or Custom.
  3. Pick a size. Each size leads with its power in kW, with a horsepower, ton or BTU/h hint alongside when that helps you find yours, like “1.5 HP pool pump · about 1.1 kW”.
  4. Set how long it runs. For Custom, enter the load in kW instead (0.1 to 22).
  5. Pick the kind of day: Sunny, Typical or Cloudy. If your plan charges different rates on weekends, a Weekday / Weekend choice appears too.

The chart and the summary above it update as you change anything. For Custom, the chart waits until you’ve entered a kW.

Each bar is a start time. It shows what the day would cost if the appliance started then, compared with the day without it.

  • Green bars are the cheapest starts, within a little of the best one.
  • Amber bars are in between.
  • Red bars are the most expensive starts.

Hover or tap a bar to see when the run would start and finish, what it costs per day, how much of it runs on your solar, and how much more a month it would cost compared with the best start. Above the chart, the summary gives your Best start, Worst start and the Difference between them per day and per month.

When the difference is tiny, the summary just says Timing barely matters for this one and every bar is green.

A run that goes past midnight carries over to the early hours of the same day, at that day’s rates.

The solar share counts solar your panels make while the appliance runs, and also solar your battery stored earlier and gives back during the run. A run at 8 PM can still be mostly on your solar if the battery filled up that afternoon.

It also works the other way. A load in the middle of the day can use solar that would otherwise have filled your battery for the evening peak, so the chart prices the cost of that later, not just the rate at the time.

The three day types use your own history from the last 30 days. Typical is a normal day for your home. Sunny is one of your better solar days and Cloudy is one of your worse ones. The cheapest start often moves between them: on a sunny day it’s usually the middle of the day, when solar covers the load, while on a cloudy day it tends to slide to the cheapest rate overnight. If the choice changes your answer a lot, plan around the cloudy one.

If your plan bills demand and you have a DemandGuard rule, some bars carry a flag: a red outline and a ! above the bar. It means starting then may push your grid use over your DemandGuard target during the rule’s window. When your plan prices demand, the hover also shows how much it could add to that month’s demand charge, as an upper bound.

The check is hourly, not interval by interval, which is why it says “may”. Grid Getter never suggests raising your target to fit an appliance. If a start is flagged, pick a different one. The summary’s Best start never lands on a flagged start while an unflagged one has a price.

Central AC pre-cool, mini split pre-cool and oven pre-cook work differently from the rest. Running them early, before your peak starts, means they run less during the peak. These use a rule of thumb: a fixed share of the early run is assumed to come off the peak run. It isn’t a model of your house, your thermostat or your oven, and the tool says so under the chart. It only applies when the run finishes no more than three hours before an on-peak period later the same day. Starts that run into the peak, finish long before it, or start after it are priced like any other appliance.

  • Not enough history yet. Grid Getter needs about a week of your solar and home use. For a newer site it also tries to pull the last 30 days from Tesla. When there still isn’t enough, you get rates only: each start is priced at your rate plan alone, with no solar or battery, and the tool says it’s rates only for now. Those answers are lower confidence, and they sharpen as history builds up.
  • No rate plan. Without a plan we can’t price anything, so the chart shows how much of each run your solar would cover, with no dollar amounts. A bar is green when solar covers some of the run and gray when it covers almost none. The summary’s Best start is then the start with the most solar and Worst start the one with the least. If every start comes out the same, which is common with a large battery (see How it works), there’s no best or worst and the summary shows a dash. A Choose your plan link takes you to pick one.
  • Rates we couldn’t read. If you have a plan but Grid Getter couldn’t read it from Tesla just then, the tool says “We couldn’t read your rates right now” and shows the solar view instead. Try again in a few minutes.
  • Can’t work it out. If something goes wrong, the tool says so and offers a retry.

You don’t need this part to use the tool. It’s for anyone who wants to know where the numbers come from.

Grid Getter starts from your last 30 days and works out an ordinary day for your home, hour by hour: how much power the house uses and how much your panels make. Typical uses the middle of your solar days. Sunny uses roughly your best day in ten, and Cloudy roughly your worst.

Then, for each of the 24 start times, it adds the appliance’s power for as long as it runs and plays the whole day through again.

Your battery is part of that replay. It charges from solar the house doesn’t need and covers the house when solar falls short, down to your backup reserve. We play the day twice in a row, so the battery starts the morning where it would really be after the night before.

Whatever the house still buys from the grid, less anything it would have sold back, is priced at your plan’s rate for that hour. Each bar is the difference between that day and the same day without the appliance.

Why the solar share can be the same at every hour

Section titled “Why the solar share can be the same at every hour”

With a big battery, nearly all your spare solar gets stored for later instead of being sold back. So wherever you put the run, it draws on the same stored solar, and every start shows the same share. That’s normal.

Picture a line from the cheapest start to the most expensive one. Starts within about a fifth of the way along are green, starts more than about two fifths along are red, and the rest are amber.

It doesn’t check whether your battery or DemandGuard can handle an appliance at the time you already run it. It also doesn’t connect to your thermostat, pool controller or EV charger, so every size is a preset estimate, not something we measured on your appliance.